5Pcs Speed Measuring Sensor Switch Counter Motor Test Groove Coupler Module Geekcreit for Arduino - products that work with official Arduino boards
71
Direct purchase from the factory 
Tuta Solutio
Donum Gratis
Politica Missilis
Politica ReditusDonum Gratis
Salve ad Roymall, tuum destinatum ad dona premium. Gratias agimus pro tuo auxilio, et offerimus donum gratis cum omni emptione. Paratus ad explorandum nostram collectionem? Perlege nostra selectio, fac ordinationem tuam, et expecta donum tuum gratis cum emptione.Politica Missilis
Processamus ordinationes intra 2 dies.Norma missilis tempus est 5-7 dies laboris.Tempus missilis potest variari secundum destinationem.1. Politica Reditus
Accipimus solum res emptas ex roymall.com. Donum gratis non potest reddi. Res debet esse non usata et in originali packaging.Processamus reditus intra 3-5 dies laboris post receptionem.Res personalisatae non possunt reddi.Contacta nos: service@roymall.com vel Whatsapp: +86193598494712.Politica Pecuniae Redditae
Accipies plenam pecuniam redditam post receptionem et inspectionem. Sumptus missilis non redditur.Contacta nos: service@roymall.com vel Whatsapp: +8619359849471
5Pcs Speed Measuring Sensor Counter Motor Test Groove Coupler Module For
Application:
Widely used in motor speed detection, pulse count, the position limit, etc.
Feature:
Using imported groove optical coupling sensor, width 5mm.
It have the output state light, if output high level, the lights are off. if output low level ,it on.
If it covered,it will output high level;otherwise it output low level.
Good signal and waveform, with strong driving ability for more than 15mA.
The working voltage of 3.3V to 5V.
Output: digital switch output (0 and 1).
Equipped with a fixed bolt hole, easily install.
Small board PCB size: 3.2 cm x 1.4 cm.
Use the LM393 wide voltage comparer.
Specification:
The DO output interface can be directly connected to a micro-controller IO port, if there is a block detection sensor, such as the speed of the motor encoder can detect.
DO modules can be connected to the relay, limit switch, and other functions, it can also with the active buzzer module, compose alarm.
Wiring specification:
VCC Connect the positive 3.3 5 v power supply
GND Connect power negative
DO TTL switch signal output
AO This module does not work
Package included:
5 x Speed Measuring Sensor Module
Application:
Widely used in motor speed detection, pulse count, the position limit, etc.
Feature:
Using imported groove optical coupling sensor, width 5mm.
It have the output state light, if output high level, the lights are off. if output low level ,it on.
If it covered,it will output high level;otherwise it output low level.
Good signal and waveform, with strong driving ability for more than 15mA.
The working voltage of 3.3V to 5V.
Output: digital switch output (0 and 1).
Equipped with a fixed bolt hole, easily install.
Small board PCB size: 3.2 cm x 1.4 cm.
Use the LM393 wide voltage comparer.
Specification:
The DO output interface can be directly connected to a micro-controller IO port, if there is a block detection sensor, such as the speed of the motor encoder can detect.
DO modules can be connected to the relay, limit switch, and other functions, it can also with the active buzzer module, compose alarm.
Wiring specification:
VCC Connect the positive 3.3 5 v power supply
GND Connect power negative
DO TTL switch signal output
AO This module does not work
Package included:
5 x Speed Measuring Sensor Module
Electronics Ranking
,
